Tengbo Ma, Kunpeng Ruan, Yongqiang Guo*, Yixin Han and Junwei Gu*. Controlled length and number of thermally conductive pathways for copper wire/poly(lactic acid) composites via 3D printing. SCIENCE CHINA Materials, 2023, doi.org/10.1007/s40843-023-2540-9. 2022IF=8.1.
https://www.sciengine.com/SCMs/doi/10.1007/s40843-023-2540-9
Abstract
Thermal conduction pathways play a crucial role in understanding the thermal behavior of thermally conductive polymer composites, yet there is a lack of in-depth research on the mechanism of how the properties of thermal conduction pathways (length, number) affect the thermal conductivity of polymer composites. In this study, one-dimensional copper wire/poly(lactic acid) (1D Cw/PLA) thermally conductive composites with controllable length and quantity of copper wire (Cw) thermal conduction pathways were fabricated using 3D printing technology. A thermal conduction model for polymer composites with one-dimensional thermal conduction pathways was established, elucidating the quantitative relationship between the properties of thermal conduction pathways and their thermal performance. With the same Cw content, the in-plane thermal conductivity (λ//) of 1D Cw/PLA thermally conductive composites is positively correlated with the number and length of thermal conduction pathways. When the Cw volume fraction is 25.1 vol%, the λ// of the 1D Cw/PLA thermally conductive composites containing 20 Cw intact thermal conduction pathways can reach up to 4.23 W/(m·K), which is 87.2% higher than the λ// of the 1D Cw/PLA thermally conductive composites without Cw intact thermal conduction pathways (2.26 W/(m·K)), 72.0% higher than the λ// of the 1D Cw/PLA thermally conductive composites containing short Cw (2 intact Cw, 18 broken at 1/2 point Cw) (2.46 W/(m·K)), and 1527% higher than the λ// of the pure PLA matrix (0.26 W/(m·K)). Using the thermal conduction model and empirical equations constructed in this study, the thermal conductivity of 1D Cw/PLA composites was predicted, and it was found that there was no significant difference between the predicted values and the measured values at a 95% confidence level.
導熱通路對理解導熱高分子復合材料的導熱行為至關重要，但目前有關導熱通路屬性（長度、數量）對高分子復合材料導熱系數的影響機制缺乏深入的研究。本文采用3D打印技術制備了銅線（Cw）導熱通路長度和數量可控的一維銅線/聚乳酸（1D Cw/PLA）導熱復合材料，建立了針對一維導熱通路的高分子復合材料的導熱模型，明晰了其導熱通路屬性與其導熱性能的定量關系。相同Cw用量下，1D Cw/PLA導熱復合材料的面內導熱系數（λ//）與導熱通路的數量和長度成正相關。當Cw體積分?jǐn)?shù)為25.1 vol%時，含20根Cw貫穿導熱通路的1D Cw/PLA導熱復合材料的λ//最高可達4.23 W/(m·K)，比相同Cw用量下不含Cw貫穿導熱通路的1D Cw/PLA導熱復合材料λ//（2.26 W/(m·K)）高87.2%，比相同Cw用量下含短Cw（2根貫穿的Cw，18根在1/2處被打斷的Cw）的1D Cw/PLA導熱復合材料的λ//（2.46 W/(m·K)）高72.0%，較純PLA基體的λ//（0.26 W/(m·K)）提高了1527%。采用本文構建的導熱模型和經驗方程對1D Cw/PLA復合材料的導熱系數進行預測，95%的置信度認為預測值與實測值無顯著差異。
論文亮點
1. 采用3D打印技術制備了導熱通路長度和數量可控的一維銅線/聚乳酸（1D Cw/PLA）導熱復合材料，明晰了導熱通路長度和數量與導熱系數的定量關系。
2. 相同Cw用量下，1D Cw/PLA導熱復合材料的λ//與導熱通路的數量和長度成正相關。當Cw體積分?jǐn)?shù)為25.1 vol%時，含貫穿導熱通路的1D Cw/PLA導熱復合材料的λ//最高可達4.23 W/(m·K)，較純PLA基體的λ//（0.26 W/(m·K)）提高了1527%。
3. 95%的置信度認為采用本文建立的導熱模型和經驗方程預測的導熱系數與實測值無顯著差異。
點擊查看更多詳情